Click For More Info

 

 

In this article down the page you will find some very good information and facts with regards to Installing A Bathtub.

Mounting a tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bath tub with a brand-new one is likewise a reasonably hard job. If the old tub is readily accessible, the task can relocate rapidly; if you have to open up a wall surface to eliminate the old tub and also place the brand-new bath tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require a helper to leave the old tub and set in the new one. Make sure you have actually certified on your own for the task as well as are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed project, it is much better to think about employing one before you start. Chances are you may need an expert plumber to make tube connections.
This article will help you install a brand-new tub in your shower room if you have already bought a brand-new tub as well as don't require to alter the setup of your previous water pipes.
Your tools and material checklist need to consist of the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Planning for the Installment

To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is important to make sure that if the faucet includes a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last position.

 

 

Removing Old Touches

If you need to change old taps with new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be rather bothersome because of the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the continuing to be water that will come from the pipelines. Once the supply pipelines have been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.

 

 

Setting up the Bath tub

Using the two wood boards under its feet, position the bathtub in the needed placement. The wood boards are useful in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the tub till the spirit level reads degree.
To mount faucets, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water system as well as examine all joints and new pipework for leakages as well as tighten them if needed. Load the bath tub as well as also check the overflow outlet and the normal outlet for leaks.
Lastly, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub ought to wait until the bathtub has been used at least once as this will resolve it right into its last placement.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bath tub

In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break a rigid seal, creating the water to penetrate the wall surface in between the bath and also the tiling, resulting in complications with moisture and also possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealant can fracture relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the marketplace. It is suggested to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I am very intrigued by How to Install a Bathtub Yourself and I'm hoping you enjoyed the entire post. Enjoyed reading our article? Please share it. Let another person find it. Bless you for your time. Come back soon.

Show Details